High Quality Chinese Hub Bearings 776900X
Introduction:A worn or damaged hub bearing or hub unit can cause unsuitable and costly failures in your vehicle's journey and even cause damage to your safety. Please pay attention to the following items during the use and installation of the hub bearing:
As shown in Figure 1, in order to ensure maximum safety and reliability, it is recommended that you always check the hub bearing regardless of the length of the car - note the early warning signal of the bearing wear: including any friction noise or suspension combination when rotating The wheel does not decelerate normally when cornering.
For rear-wheel-drive vehicles, it is recommended to lubricate the front hub bearings when the vehicle travels to 38,000 km. When replacing the brake system, check the bearings and replace the oil seal.
2, if you hear the noise from the bearing parts of the hub, first of all, it is important to find the location where the noise occurs. There are many moving parts that may produce noise, or some rotating parts may come into contact with the non-rotating parts. If it is confirmed that the noise is in the bearing, the bearing may be damaged and needs to be replaced.
3. Because the front hub results in similar working conditions for the failure of the bearings on both sides, it is recommended to replace them in pairs even if only one bearing is broken.
As shown in Figure 4, the hub bearings are sensitive and in any case require the right method and the right tool. The components of the bearing must not be damaged during storage and installation. Some bearings require a large pressure to press in, so special tools are required. Be sure to refer to the car manufacturer's instructions.
5, when installing the bearing should be in a clean and tidy environment, the entry of fine particles into the bearing will also shorten the service life of the bearing. It is very important to keep the environment clean when replacing bearings. It is not allowed to hit the bearing with a hoe, pay attention to the bearing not to fall to the ground (or similarly improper handling). The condition of the shaft and housing should also be checked before installation. Even minor wear can cause poor fit and cause early failure of the bearing.
The next is the hub bearing on Hot Sales for your information:
| MFG: | Part #: | Bearings Used |
|---|
| American Classic Wheels | | |
| | 130 | 6803 X 7 |
| | 350 | 688 X 2 F, 6803 X 4 R |
| | 420 (OLD) | 609 X 2 F, 6803 X 4 R |
| | 420 (NEW) | 688 X 2 F, 6803 X 4 R |
| | Carbon 38 | 688 X 2 F, 6803 X 4 R |
| | Carbon 58 | 688 X 2 F, 6803 X 4 R |
| Bontrager Wheels | | |
| | Race, Race Lite | 6000 X 2 F, 6902 X 2 R |
| | Aeolus 6.5 | 6803 X 2 F 6902 X 2 R |
| | Comp | 6802 X 2 F 6902 X 2 R |
| | Pro Series | 6802 X 2 F, 6902 X 2 R |
| | X Lite | 6803 X 2 F, 6902 X 2 R |
| | XXX Lite | 6803 X 2 F, 6902 X 2 R |
| Campagnolo Wheels/Hubs | | |
| | Record, Shamal (8/9) | 609 X 2 F, 6001 X 2 R |
| | Chorus (8/9) | 609 X 2 F, 6001 X 2 R |
| | Neutron, Bora, Hyperon | 5/32" X 36 F, 5/32" X 36 R |
| | Khamsin, Zonda, Eurus | 5/32" X 36 F, 5/32" X 36 R |
| | Shamal, Proton | 5/32" X 36 F, 5/32" X 36 R |
| | Pista | 1/4" X 18" F, 1/4" X 18 R |
| DT Swiss Hubs | | |
| | DT 340 Road | 6000 X 2 F, 6000 X 2+ 6900 X 2 R |
| | DT 340 Mtn | 6000 X 2 F, 6000 X 4 R |
| | Onyx Road | 6000 X 2 F, 6000 X 4 R |
| | Onyx Mtn | 6001 X 2 F, 6000 X 1+ 6900 X 2 R |
| | 240 Road and Mtn | 6802 X 2 F, 6902 X 2+ 6802 X 2 R |
| | 240 Mtn | 6802 X 2 F, 6902 X 4 R |
| | 240 Disc, 240S Disc Mtn | 6902 X 2 F, 6902 X 2+ 6000 X 2 R |
| | 240S Disc CL | 6902 X 2 F, 6902 X 2+ 6000 X 2 R |
| | 240S Disc Oversize Mtn | 6085 X 2 F, 6902 X 4 R |
| | 240S Road | 6802 X 2 F, 6902 X 2+ 6802 X 2 R |
| | 240S MTN | 6802 X 2 F, 6902 X 4 R |
| | 240S Radial | 6803 X 2 F, 6902 X 2 R |
| Easton/Velomax Wheels | | |
| | Ascent/ Orion | R6 X 2 F, 6901 X 3+ 6902 X 2 R |
| | Tempest/ CarbonF | R6 X 2 , 6901 X 3+ 6902 X 2 R |
| | Vista S / Circuit S | R6 X 2 F, 6000 X 2 R |
| | Circuit (Rep. freehub) | R6 X 2 F, 6901 X 3+ 6902 X 2 R |
| | XC- One | 6901 X 3 F, 6901 X 1+ 6902 X 3 R |
| | EA 90 | R6 X 2 F, 6901 X 1, 6902 X 3 R |
| FSA Wheels | | |
| | RD220C | 6900 X 2 F, 6000 X 2 R |
| | RD220S | 6900 X 2 F, 6902 X 2 R |
| | RD400C, RD400S | R6 X 2 F, 6901 X 1+6902 X 1 R |
| | RD460S, XC-300 | 6000 X 2 F, 6000 X 2 R |
| | RD488C, RD488S | R6 X 2 F, 6901 X 1+6902 X 1 R |
| | RD600C, RD600S, RD800C | R6 X 2 F, 6901 X 1+6902 X 1 R |
| | RD800S | R6 X 2 F, 6903 X 1+6902 X 1 R |
| Mavic Wheels | | |
| | Ksyrium SL3 | 6901 X 2 F, 6903 X 1+ 608 X 2 R |
| | Cosmic Carbone SL | 6903 X 2 F, 6903 X 1+ 608 X 2 R |
| | Cosmic Carbone | 6901 X 2 F, 6903 X 1+ 608 X 2 R |
| | Cross Max SL | 6901 X 2 F, 6903 X 1+ 608 X 2 R |
| | Elite | 6001 X 2 F, 6001 X 1+ 608 X 2 R |
| | Equipe | 6001 X 2 F, 6001 X 1+ 608 X 2 R |
| | Cosmic Elite | 6001 X 2 F, 6001 X 1+ 608 X 2 R |
| | Crossmax Enduro | 6001 X 2 F, 6001 X 1+ 608 X 2 R |
| | Crossland | 6001 X 2 F, 6001 X 1+ 608 X 2 R |
| | Cosmic Carbone SSC (OLD) | 6805 X 2 F, 6903 X 2+ 608 X 2 R |
| | Crossmax XL | 6901 X 2 F, 608 X 2 R |
| Reynolds Wheels | | |
| | Stratus | 6901 X 2 F, 608 X 2 R |
| | Solitude | 6901 X 2 F, 608 X 2 R |
| | 05-06 Shimano Hubs | 6901 X 2 F, 6901 X 2 R |
| | 05-06 Campy Hubs | 6802 X 2 F, 6902 X 2+ 6802 X 2 R |
| Shimano | | |
| | Dura Ace, Ultegra | 3/16" X 22 F, 1/4" X 18 R |
| | 105, Tiagra, Sora | 3/16" X 22 F, 1/4" X 18 R |
| | XTR, XT, LX | 3/16" X 22 F, 1/4" X 18 R |
| | Saint | 3/16" X 22 F, 1/4" X 18 R |
| Zipp Wheels | | |
| | 202 | 6802 X 2 F, 6802 X 3+ 6902 X 1 R |
| | 303, 404- '05 and newer | 6802 X 2 F, 6802 X 4 R |
| | 303, 404- Pre '05 | 6802 X 2 F, 6802 X 3+ 6902 X 1 R |
| | 606 | 6802 X 2 F, 6802 X 4 R |
| | 808 | 6802 X 2 F, 6802 X 4 R |
| | 900 | 6802 X 2 F, 6802 X 4 R |
| | 950 | 6802 X 2 F, 6802 X 4 R |
| | Pre '04 hubs | 6802 X 2 F, 6802 X 4 R |
Our company:
Shandong Xiujiang Bearing Co., Ltd. is a Professional and leading manufacturer and supplier of all kinds of bearings in China market, With more than 30 years experiences in producing, R&D and sales bearing lines.
1.We have our own independent brand SDSXJ
2.As a good agent for domestic and foreign brand products, such as SKF,,TIMKEN,NSK,NTN,KOYO,NACHI,IKO,LYC,ZWZ,HRB,NXZ, TWB, TMB, C&U, WANXIANG etc.
3. Affordable, Durable, &Classical
4. OEM & ODM service are available.
5. Super Quality & Favorable price
Our factory shows:
Our Package:
*industrial pakage+outer carton+pallets
*sigle box+outer carton+pallets
*Tube package+middle box+outer carton+pallets
*According to your requirments
Transportation:
1. International Express
2. By air plant
3. International Seaborne shipping
4. International railway transportation
FAQ:
1. Could you please tell me the delivery time of your goods?
3-7days stock goods and other goods according to your quantity about 3-30 days
2. How about MOQ of your product?
Our MOQ is 1 piece
3. Can you tell me the payment terms can be accepted of your company?
L/C,T/T, Western union, Paypal
4. Can you accept OEM and customize?
Yes, we can customize for you according to your sample, blueprint or drawings with parameters
5. Can you supply door to door service?
Yes, by Express(DHL, FedEx, TNT, EMS)it will take 3-7 das to your country
6. Can supply sample for free?
Yes, we can supply our clients with free sample, but you have to afford freight.
7. What certificate does your factory owned?
We have TUV and ISO9001: 2008 certificate, we can do for you if you need other certificate.
8. Are you factory or trading company?
Factory+trading company
9. How long does your bearings guarantee for?
1 year, customers need to supply us with bearings' pictures and sent the bearings back.
10. Can you tell me the material of your bearings?
Stainess steel, Gcr15(bearing steel), carbon steel, chrome steel, plastic, ceramic
11. Can you tell me the packing of your bearings?
Single plastic bag+single paper box+single or wooden case+pallet
Thanks for your time! Should you have any needs or interest, please do not hesitate to contact us.
